Marshall DSL40CR – 40W 1×12 Combo with Reverb
2,785.00 Excl. VAT
- Capable of conjuring any classic Marshall sound — past or present
- 2 channels — Classic Gain and Ultra Gain
- Each channel features 2 modes — Clean/Crunch and OD1/OD2, respectively
- High and low power modes allow you to dial in appropriate volume for any setting
- Line output with Softube cabinet emulation faithfully re-creates the sound of a Marshall 1960 Lead cabinet
- Highly effective Resonance control tailors your low-end response
- Refined EQ section gives you incredible tonal flexibility
- Studio-grade digital reverb
- Bypassable rear-panel series effects loop
- Included 2-way footswitch for channel switching and reverb on/off
Available on backorder
Marshall's Legendary DSL Is Back in Action
Tap into burly Marshall tone anywhere from your bedroom to the stage with the Marshall DSL40CR tube combo amp. With per-channel Gain and Volume controls, a dedicated Resonance control, reverb, and an effects loop, the Marshall DSL40CR is ready for your next gig or session. And with its adjustable power level, you can dial in cranked-amp tones that won’t wake your neighbors — or even use the Softube speaker-emulated output for direct recording and monitoring. Marshall even refined the EQ section for extremely versatile tone shaping. From glassy cleans to bone-rattling crunch to blistering high gain, your wish is the Marshall DSL40CR’s command.
A 40-watt tone beast
Marshall’s DSL40CR is a tube-loaded, twin-channel workhorse capable of conjuring an entire arsenal of British-flavored tones. Four ECC83s in the preamp section, in concert with the amp’s Gain/Master volume arrangement, give you stunning tone-shaping mojo, and with two EL34s in the engine room, you have the volume to rule any club in the world. While sporting the same tubes, minus two EL34s, and the same feature set as the original DSL100, this little beast has critical upgrades that give you even more control over your sound, including a Resonance control that lets you dial in your preferred amount of low-end girth, a studio-grade digital reverb, High and Low power settings, and a bypassable rear-panel series effects loop. The Marshall DSL40CR also has a 2-way footswitch for channel switching and reverb on/off.
Softube speaker-emulated output
Marshall has teamed up with software mavens Softube to create exceptional tones in their CODE series of amplifiers, and they’ve joined forces again on the DSL40CR tube combo amp. Its line output features an accurate emulation of Marshall’s iconic 1960 speaker cabinet, allowing you to plug directly into a recording chain with confidence. Guitarists at Sweetwater love flexible recording options, and the Marshall DSL40CR delivers.
| Weight | 28.2 kg |
|---|---|
| Dimensions | 74.2 × 37.4 × 63 cm |
| Type: | Tube |
| Number of Channels: | 2-channel (2 modes each) |
| Output Power: | 40W (20W power setting) |
| Speaker Size: | 1 x 12″ Celestion V-Type speaker |
| Preamp Tubes: | 4 x ECC83 |
| Power Tubes: | 2 x EL34 |
| Reverb: | Classic, Ultra |
| EQ: | 3-band EQ, Tone Shift, Resonance |
| Inputs: | 1 x 1/4″ (instrument), 1 x 1/8″ (aux in) |
| Outputs: | 2 x 1/4″ (4 ohm), 2 x 1/4″ (8 ohm), 1 x 1/4″ (internal 16 ohm speaker), 1 x 1/4″ (Softube emulated out) |
| Effects Loop: | Yes |
| MIDI I/O: | In |
| Footswitch I/O: | 1 x 1/4″ (channel, effects loop) |
| Footswitch Included: | Yes, 2-button footswitch (optional 6-way sold separately) |
| Bias Type: | Adjustable Fixed |
| Construction Material: | Black Tolex |
| Power Source: | Standard IEC AC cable |
